Massapequa Plumbing Company handles the full range of residential and commercial plumbing work, from a dripping faucet to a burst pipe in the middle of a nor'easter. Leaks, clogged drains, water heater failures, sewer backups, broken toilets: we take the call, scope the job, and get it scheduled. We are available every day from 5:00 AM to 9:00 PM, and we take short-notice work when something goes wrong without warning. Quick to arrive. Careful with your home. Clean when we leave.
Call (934) 336-5446 for a quote.
Keeping a home dry starts with the pipes behind the walls, and that is exactly where we work. We serve single-family homes, condos, apartments, multi-unit buildings, rental properties, office buildings, and commercial spaces throughout the area. Homeowners call us for repairs and upgrades. Landlords and property managers call when a tenant reports a problem. Businesses call when plumbing issues affect operations.
Nassau County's housing stock leans older, and older buildings carry older pipe. Galvanized, copper and PEX pipes each fail in their own way. Galvanized corrodes from the inside out and loses flow over time. Copper develops pinhole leaks at joints. PEX can fail at fittings if the original installation was rushed. We know what to look for and what the fix actually involves. Drain and pipe work is carried out to code, whatever the building type. One call, and the visit is booked.
Plumbing work like this is the everyday end of the trade, and it is where most calls start. A slow drain in a kitchen sink is usually grease and food debris narrowing the line. A shower that barely drains is hair and soap buildup at the trap. A floor drain that backs up in a finished basement is a sign the line further down needs attention.
We clear clogs at the fixture, at the trap, and further down the line when the blockage is deeper. For stubborn buildup or root intrusion on a main line, hydro jetting clears the pipe wall without just pushing the problem further along. We tell you what we found and what it took to clear it. We'll get the job plumbed and finished.
When the plumber arrives, the real work begins. A wet spot on a ceiling or a wall that will not dry tells you water is moving somewhere it should not be. Finding it is the first job. We use pressure testing and visual inspection to trace the line and locate the source before anything is opened up.
Leaks turn up under sinks, at supply line connections, behind walls, and at shutoff valves that have not been exercised in years. The cause is found before anything is replaced. We treat your home and its pipes the way we would our own. Pricing agreed up front. Code-compliant work. Reliable water.
Don't let a small leak turn into a flooded floor: a water heater that is showing rust at the base, producing inconsistent temperature, or simply not delivering hot water at all needs attention before the tank gives out completely.
We handle tank and tankless water heaters, both repair and full replacement. A unit that is making noise or running out of hot water faster than it used to may only need a component replaced. A tank that is corroding at the connections or past its useful life is a replacement job. We assess the unit, look at the pipe connections and the shutoff valve feeding it, and give you a clear picture of what the repair or swap involves. One call gets the leak looked at.
Don't let a small leak turn into a flooded floor, and do not let a running toilet add to a water bill for another month. We repair and replace toilets, faucets, showers, bathtub plumbing, outdoor faucets, hose bibs, and garbage disposals. Kitchen and bathroom fixtures, both.
Prompt response, even for last-minute plumbing calls, matters when a faucet will not shut off or a garbage disposal has seized. We install new fixtures, swap out aging ones, and handle the supply line and shutoff valve work that goes with the job. Where backflow prevention is part of the fixture installation, we address that as part of the scope. We'll get the job plumbed and finished.
A sewer backup shows up fast. Drains across the house slow down or stop. Water comes up in the lowest fixture. The smell is unmistakable. When that happens, the problem is almost always in the main line running from the house out to the city connection, not in a single fixture drain.
We clear main line blockages, run camera inspections to identify the failure point, and handle repairs and replacements when the line itself is compromised. Where the ground conditions and the pipe's location allow it, trenchless methods can replace a damaged section without tearing up the yard. We speak only to the line: from the house to where it meets the city connection. One call, and the visit is booked.
Low water pressure is not always a supply problem. Mineral buildup inside aging galvanized pipe reduces the interior diameter over time until the flow drops noticeably. A failing pressure regulator can affect the whole house. A corroded shutoff valve that was never fully opened after a repair can choke a single fixture line.
We diagnose the cause before recommending a fix. Sometimes it is a valve. Sometimes it is a regulator. Sometimes the pipe itself needs to go. Individual shutoff valves and the main water shutoff can be repaired or replaced as a standalone job. When the pipe throughout the house is the source of the problem, a whole-home repipe is the longer-term answer. We cover that in detail in the section below.
Long Island's older neighborhoods, including much of Massapequa, carry a mix of pre-1960s and pre-1980s construction. That means aging pipe materials, high water tables, coastal moisture, and basements that see real stress during heavy rain and storm surge. The three services below come up regularly here because the conditions that drive them are part of living on this part of the island.
Homes with original galvanized pipe are running out of time. The pipe corrodes from the inside, and by the time water pressure drops and rust discoloration shows up at the faucet, the pipe wall is already compromised. Aging copper with a history of pinhole leaks tells a similar story. A whole-home repipe replaces the supply pipe throughout the house, line by line, restoring full flow and pressure. Material options include copper and PEX, and we walk through what each involves before the job starts.
Many Long Island homes were built with clay or cast-iron sewer lines that have been in the ground for sixty or seventy years. Root intrusion, ground movement, and simple age cause these lines to crack, offset, or collapse. A camera inspection of the line shows exactly where the failure is and how extensive it runs. Depending on what we find, the line can be replaced by open-cut excavation or by trenchless methods that limit disruption to the yard. We handle the line from the house to the city connection.
Nassau County's water table is high, and the basements here reflect it. A heavy rainstorm, a slow nor'easter, or a period of sustained wet weather can push groundwater up through the floor if the drainage system is not doing its job. We install sump pumps, set the discharge line to move water well away from the foundation, and configure the float switch to activate before the water level becomes a problem. Backup options are worth discussing for homes that have seen flooding before.
Burst pipes, major leaks, sewer backups, no hot water, a basement taking on water: these are not problems that wait until Monday morning. We are available every day from 5:00 AM to 9:00 PM for urgent calls, and we take short-notice work when conditions are serious. Simple scheduling. A price settled on the call. Water back fast.
When you call, we scope the situation on the phone, give you a price, and get the visit on the schedule. We do not leave you guessing about what the call will cost before anyone shows up.
Plumbing work like this is the everyday end of the trade, and getting a price should not be complicated. Call us, describe what is happening, and we give you a rate on the phone before anything is scheduled. The price is confirmed before the visit starts, and we explain what it covers.
We are available every day from 5:00 AM to 9:00 PM. Whether you are scheduling routine fixture work, a water heater replacement, or something that came up this morning, the process is the same: call, get a price, get it on the calendar. One call gets the leak looked at.
We serve Massapequa and the surrounding communities throughout Nassau County. That includes Massapequa Park, Seaford, Wantagh, Merrick, Bellmore, Farmingdale, Amityville, and Lindenhurst just across the Suffolk County line. If you are in the area and need a plumber, call and we will confirm we can get to you.
Low pressure throughout a home is often a sign that the supply lines have corroded internally over time. Galvanized pipe, common in homes built before the 1970s across Nassau County, narrows from the inside as it oxidizes, reducing flow to every fixture it feeds. A failing pressure regulator or a shutoff valve that was never fully reopened after a past repair can also be the cause. We diagnose the source before recommending a fix, whether that is a single valve, a corroded section, or the full supply system.
A clog in a single fixture drain, such as a kitchen sink or a shower, usually affects only that drain. When multiple drains in the house slow down or back up at the same time, or water comes up in the lowest fixture when another drain is used, the blockage is almost certainly in the main sewer line. We diagnose the location before clearing anything, so the work addresses the actual source. A camera inspection of the main line shows exactly where the blockage is and what caused it.
We are available every day from 5:00 AM to 9:00 PM and take short-notice work when something goes wrong without warning. When you call about an urgent situation, we scope it on the phone, confirm availability, and schedule the visit as quickly as the calendar allows. We do not leave you guessing about timing or cost before anyone arrives.
Call (934) 336-5446 and describe what is happening.
A water stain on a ceiling or wall that keeps coming back after drying is one of the clearest signs. A persistent mildew smell in a room with no visible moisture source, soft spots in flooring, or a water bill that has spiked without an obvious explanation all point toward a leak that has not surfaced yet. We use pressure testing and, where needed, other detection methods to locate the source before opening anything up. Finding the leak first limits the work to where it is actually needed.
A spot repair makes sense when the problem is isolated to a single fitting or a short section of pipe. When leaks keep coming back at different points throughout the house, water pressure is consistently low at every fixture, or the water runs discolored when a faucet is first opened, the supply pipe itself is usually the source. Whole-home repiping replaces the supply lines throughout the house and eliminates the cycle of recurring spot repairs. We assess the system and explain what the inspection shows before recommending either approach.
Sewer line replacement addresses the lateral running from the house to the municipal connection. In established Massapequa neighborhoods, those lines are often clay or cast iron that has been in the ground for decades, and they crack, shift, or collapse as the ground moves and the material ages. We inspect the line with a camera first to identify where the failure is and how far it extends. Depending on what the inspection shows, we replace the affected section or the full run, using trenchless methods where site conditions allow.
A tank water heater that runs out faster than it once did is usually dealing with sediment buildup at the bottom of the tank, a failing heating element, or a thermostat that is no longer regulating correctly. In some cases the unit has simply reached the end of its useful life and the recovery rate has declined permanently. We diagnose the unit before recommending a repair or replacement, and we explain what each option involves. If a replacement makes more sense than a repair, we walk through what the installation covers.
A tank water heater stores a set volume of hot water and reheats it as it is used. A tankless unit heats water on demand and does not maintain a stored supply. Tankless units are more common in newer installs and in homes where space or energy use is a factor. Most Nassau County homes still run on tank units, and both formats are part of the work we handle. We explain what each option involves for your specific setup so you can make the decision with the full picture.
Someone needs to be present to provide access to the property and to the areas where the work will be done. That does not have to be the homeowner, but it should be someone who can show the plumber where the problem is and where the main water shutoff is located. If access arrangements need to be worked out in advance, mention that on the call when we schedule the visit.
Most plumbing repairs require shutting off the water supply to the affected area or to the whole house for at least part of the visit. How long the water is off depends on the scope of the work. For a faucet or fixture repair, the shutoff is usually brief. For repiping or main line work, the water may be off for a longer stretch. We let you know what to expect before the visit starts.
Clearing the area under the sink, around the water heater, and along any wall or floor where the problem is located helps the visit start without delay. If the main water shutoff is in a utility area or a closet, making sure it is accessible before the plumber arrives is useful. We handle the work itself. Anything that makes the access point easier to reach saves time at the start of the job.
We handle both installation and replacement. A disposal that hums but will not turn, trips its reset repeatedly, or leaks at the base is usually worth a service call to determine whether repair is practical. When the unit is past repair or a homeowner wants to upgrade, we remove the old disposal and install the new one, including the drain connection and the supply side where needed. Disposal work often comes up as part of a kitchen drain service call.
Massapequa Plumbing Company is available every day from 5:00 AM to 9:00 PM. When something goes wrong with the plumbing in your home or building, the right move is a phone call. We answer, we scope the job, and we give you a price before anything starts. Quick to arrive. Careful with your home. Clean when we leave.
Call (934) 336-5446 to get a quote and get the work scheduled.
We handle the full range of plumbing work in Massapequa and across Nassau County, from a dripping faucet to a failed sewer line. The table below breaks down what each service covers, who it fits, and what is worth knowing before you call. Every visit starts with a price confirmed on the phone, and the work is carried out to code whatever the job involves.
Call (934) 336-5446 to get a quote and get it on the schedule.
| Service | What's Included | Typical Situations | Worth Knowing |
|---|---|---|---|
| Water Heater Repair & ReplacementMost Popular | Tank and tankless units, Component repair or full replacement, Supply line and shutoff valve check, Assessment before any recommendation | No hot water, inconsistent temperature, rust at the base, or a unit making unusual noise | A unit running out faster than it used to may need a component replaced rather than a full swap |
| Sewer & Main Line Service | Main line blockage clearing, Camera inspection of the line, Repair and replacement of damaged sections, Trenchless methods where site conditions allow | Multiple slow drains, backups at the lowest fixture, or an unmistakable sewer odor | We speak only to the line from the house to the city connection, and camera inspection shows exactly where the failure is |
| Whole-Home Repiping | Galvanized and aging copper replacement, PEX or copper supply line installation, Line-by-line replacement throughout the house, Pressure and flow restoration | Homes with recurring pinhole leaks, discolored water, or consistently low pressure at every fixture | Nassau County homes built before the 1970s often have galvanized pipe that has corroded internally to the point where spot repairs no longer hold |
| Toilet Repair & Installation | Running toilet diagnosis and repair, Full toilet replacement, Flapper, fill valve, and flush valve work, Supply line and shutoff valve service | A toilet that runs constantly, leaks at the base, or will not flush properly | A running toilet can add significantly to a water bill over a few weeks |
| Garbage Disposal Service | Disposal repair and reset, Full unit replacement, Drain connection and supply side work, Installation of new units | A disposal that hums but will not turn, trips repeatedly, or leaks at the base | Disposal work frequently comes up during a kitchen drain service call |
| Faucet & Fixture Installation | Kitchen and bathroom faucets, Shower and tub fixtures, Outdoor faucets and hose bibs, Supply line and backflow work where required | Dripping, leaking, or aging fixtures ready for repair or upgrade | Fixture work often includes the supply line and shutoff valve as part of the same job |
| Leak Detection & Repair | Pressure testing to locate the source, Supply line and shutoff valve leaks, Behind-wall and under-floor tracing, Repair after source is confirmed | Unexplained wet spots, recurring stains, or a water bill that has climbed without explanation | We find the source before opening anything up, which limits the work to where it is actually needed |
| Water Pressure & Shutoff Valve Repair | Pressure regulator diagnosis and replacement, Shutoff valve repair or replacement, Mineral buildup assessment in older pipe, Whole-house and fixture-level pressure work | Low pressure at every fixture or a single line that has dropped flow after a past repair | A valve that was never fully reopened after a prior repair is a common and easy-to-miss cause of low pressure |
| Sump Pump & Basement Drainage | Sump pump installation and replacement, Discharge line placement, Float switch configuration, Backup options for flood-prone homes | Basements in Nassau County with a high water table or a history of water intrusion during storms | The discharge line placement matters as much as the pump itself, water needs to move well away from the foundation |
| Drain Cleaning & Clog Removal | Fixture and trap clearing, Main line blockages, Hydro jetting for stubborn buildup, Root intrusion removal | Slow or stopped drains at any fixture or throughout the house | Hydro jetting clears the pipe wall rather than just pushing debris further along the line |
| Sewer Line Replacement | Camera inspection before any excavation, Clay and cast-iron line replacement, Open-cut or trenchless methods, Full lateral from house to city connection | Older Long Island homes with cracked, offset, or collapsed sewer laterals | Many Massapequa sewer laterals are clay or cast iron that has been in the ground for sixty or more years |
| Emergency Plumbing | Burst pipe response, Major leak containment, Sewer backup service, No-hot-water calls | Urgent situations that cannot wait, available every day from 5:00 AM to 9:00 PM | We scope the situation on the phone and give a price before anyone is dispatched |
What are the signs that a faucet or fixture needs to be replaced rather than repaired?
A faucet that drips after the handle is fully closed, one that has visible corrosion at the base, or one where the cartridge or valve seat has worn past the point of a simple reseat is usually a replacement candidate. Fixtures with cracked bodies or fittings that have been repaired more than once tend to fail again at a different point. We look at the fixture and the supply connections together and tell you which direction makes more sense before any parts are ordered.
How do tree roots get into a sewer line, and how is that repaired?
Roots follow moisture, and a sewer line that has a small crack or a slightly offset joint gives roots a path in. Clay pipe, which is common in older Nassau County and Long Island neighborhoods, is especially vulnerable because the joints are not sealed the way modern pipe connections are. Once roots are inside the line they expand and eventually block flow entirely. We run a camera to confirm where the intrusion is, clear the roots, and assess whether the pipe at that point needs to be repaired or replaced to prevent the problem from coming back.
What does hydro jetting do that a standard drain snake cannot?
A drain snake breaks up a clog and pulls debris out, but it does not clean the pipe wall. Grease, scale, and mineral buildup that coats the inside of a drain line stays in place after snaking and continues to narrow the pipe. Hydro jetting uses pressurized water to scour the pipe wall from the inside, removing the buildup rather than just punching through it. For a line that keeps clogging in the same spot, or a main line with years of accumulation, hydro jetting addresses the cause rather than the symptom.
Cause Found Before Anything Is Replaced
We locate the source of a leak, a clog, or a pressure problem before recommending a fix. That means the work addresses what is actually wrong rather than what is easiest to reach.
When is it worth calling a plumber instead of trying to fix a clog yourself?
A single slow drain that responds to a plunger is a reasonable DIY situation. When the drain does not clear after a few attempts, when multiple fixtures are backing up, or when the problem keeps returning within a few days, the blockage is likely further down the line or more substantial than a plunger can reach. Attempting to clear a main line clog with store-bought chemicals or a short consumer snake can push debris further along without resolving it. We diagnose the location first so the work addresses the actual source.
How long does a whole-home repipe typically take?
The time depends on the size of the home, the number of fixtures, and the pipe material being installed. A single-story home with a straightforward layout can often be repiped in one to two days. A larger home or one with more complex access points takes longer. We walk through the scope before the job starts so you know what to expect in terms of access, water shutoff time, and how the work will be sequenced. The goal is to minimize the time the water is off and to leave each section ready for use before moving to the next.
What causes a sump pump to fail, and how do I know mine is not working?
The most common causes of sump pump failure are a burned-out motor, a stuck or misadjusted float switch, a clogged intake screen, or a discharge line that has frozen or become blocked. A pump that runs constantly without moving water is usually dealing with a float switch problem or a discharge line issue. A pump that does not run at all when water is present in the pit may have a motor failure or a tripped breaker. In Nassau County, where the water table is high and basements take on water during heavy rain, a pump that is not tested periodically can fail exactly when it is needed most. We inspect the pump, the float, and the discharge line as part of any sump pump service call.
Older and Newer Plumbing Both Handled
Galvanized, copper, and PEX each fail differently, and Nassau County homes carry all three. We work with whatever is in the walls and explain what the material means for the repair.
What is involved in replacing a lead service line?
A lead service line is the pipe that runs from the water main at the street into the home. Older homes in Nassau County and across Long Island may still have original lead laterals that were never replaced. Replacement involves excavating the line from the curb stop to the point where it enters the house, removing the lead pipe, and installing a new copper or approved plastic line in its place. The work typically requires coordination with the municipality regarding the curb stop and the street-side connection. We handle the house-side portion and walk through what the full scope involves before the job starts.
How is a sump pump discharge line set up to actually move water away from the foundation?
The discharge line needs to terminate well away from the foundation and at a point where the water can drain freely without pooling back toward the house. A line that terminates too close to the foundation, or one that discharges into a low spot in the yard, can cycle water back toward the basement during a heavy rain. We set the discharge line to move water to a point in the yard with positive drainage, and we confirm the outlet is not obstructed and will not freeze in cold weather. For homes that have flooded before, we also discuss backup pump options in case the primary unit is overwhelmed.
Scope Agreed Before Any Pipe Is Cut
The price and the scope are settled on the call before the visit starts. You know what the job covers and what it costs before anyone touches a fitting.
Can cast-iron drain stacks be repaired, or do they need to be replaced?
Cast-iron drain stacks in older homes can develop cracks, rust-through sections, or joint failures that cause leaks inside the wall or at the floor. A single compromised section can sometimes be cut out and replaced with a compatible fitting and a short section of new pipe. When the stack has deteriorated along its full length, or when multiple sections are failing, a full replacement is the more practical answer. We inspect the stack, identify where the failures are, and explain what a repair versus a full replacement involves before recommending either.
What should I do if a pipe bursts while waiting for a plumber?
The first step is to shut off the water supply to the affected area or, if you cannot isolate it, to shut off the main water shutoff for the house. Knowing where your main shutoff is before an emergency happens saves time when it matters. Once the water is off, move anything that can be damaged away from the area and contain standing water if you can do so safely. When you call us, describe where the break is and whether the water is off so we can scope the job accurately on the phone and get the visit scheduled as quickly as the calendar allows.
How are estimates handled for larger jobs like repiping or sewer line replacement?
For larger jobs, the price is based on the scope of the work, and the scope is determined by what we find during the assessment. For a repipe, that means looking at the pipe material throughout the house, the number of fixtures, and the access points. For a sewer line replacement, it means running a camera inspection to see where the failure is and how far it extends. We give you a clear picture of what the job involves and what it costs before any work starts. The price is confirmed before anything is scheduled, and we explain what it covers.
Call (934) 336-5446 to describe what you are dealing with and get a price before anything is scheduled.
(934) 336-5446